EL-Cut
Accuracy and reproducibility of electrochemical tests do not solely depend on the choice of materials but also on simple geometric and mechanical parameters. The proper cutting of the electrodes is an often neglected factor. Torn and chipped electrode edges – although invisible to the bare eye – inevitably cause current inhomogeneity and are thus likely […]
PAT-Stand-1
The PAT-Stand-1 is a docking station, which runs a single PAT-Cell or PAT-Cell-Press. It can be connected directly to a common multi-channel potentiostat (such as those from Ivium or PalmSens) or battery testers (like Ivium or BaSyTec) using 4mm banana sockets or a hardwired Sub-D socket. Therefore, the PAT-Stand-1 saves wiring effort, because it is […]
885 Fuel Cell Potentiostat
Scribner Associates extends its ground-breaking line of tabletop fuel cell testing equipment with the 885 Fuel Cell Potentiostat. The 885 bolts directly to the 850 Multi-Range Fuel Cell Test Systems or 890e / 890C / 890ZV Fuel Cell Test Loads. This, together with Scribner’s FuelCell software results in an integrated and efficient fully automated testing […]
IviumSoft
Ivium Potentiostats are controlled by IviumSoftTM Electrochemistry Software, provided free of charge. Developed by Ivium engineers, IviumSoft is feature-rich, yet intuitive. It is used for both data acquisition and data analysis, and controls the potentiostat for a broad range of electrochemical techniques. IviumSoft also includes a wide range of data evaluation and analysis tools. IviumSoft […]
Electroflow MTF Multi-cell Electrolyser Test Fixture
The ElectroFlow MTF is a multi-cell electrolyser test fixture that is fully compatible with the ElectroFlow ETS20. The advanced design of the ElectroFlow MTF supports concurrent operation and testing of multiple electrolyser cells. Available in two sizes (4.9cm2 and 15.9cm2 active cell areas), the ElectroFlow MTF enables evaluation and performance comparison of key components, such […]
PAT-Clamp-1
Docking Station with Minimised Dimensions The PAT-Clamp-1 is our smallest docking station for a single PAT test cell. It was developed for tight space constraints. The socket can be left connected permanently to a common potentiostat or battery tester using 2 mm banana sockets or Sub-D connector. Therefore there is no need to renew the […]
ECC-CellLoad
Electrode alignment and assembly tool When building full cells with thin Celgard type separators, the concentric alignment of the two electrodes – with the oversized separator in between – is the key for electrochemical performance and life time. The ECC-CellLoad is the tool to get that done easily. This tool is suitable for test cells […]
PAT-Stand-16
The PAT-Stand-16 is the docking station for up to 16 PAT-Cells in 4 x 4 matrix. The PAT-Stand-16 has a built-in data logger recording full and half cell voltages, cell current, tray temperature and time. The PAT-Stand-16 can be connected permanently to a usual multi-channel potentiostats (such as those from Biologic or Ivium) or battery […]
EL-Cell Metal Seal Mounting Kit
Tool kit for using metal seals in PAT series test cells EL-CELL offers metal sealing rings for PAT series test cells for highest demands on cell tightness. This tool kit is designed to ensure the correct installation when using these metal seals. The handy assembly block holds the cell in place, while the torque wrench […]
ECD-4 Nano Dilatometer
The ECD-4-nano takes dilatometry measurements to the next level The ECD-4-nano is a high-resolution electrochemical dilatometer. The most powerful version offers a capacitive parallel plate sensor system with a resolution of better than 5 nanometers. This makes the ECD-4-nano the perfect instrument for detecting thickness changes of the individual electrode or the full cell stack […]